|
| |
|
|
Dielectric properties of epoxy resins
Matoušová, Klára ; Novák, Vítězslav (referee) ; Kazelle, Jiří (advisor)
This diploma thesis deals with the fundamental properties of epoxide mixtures, as determining of these fundamental properties of epoxide mixtures could in the case of favorable results lead to diminishing the amount of defects in epoxide-embedded instrument transformers. As the influence of effects in the manufacturing process of transformers causing poor quality is very extensit, the biggest emphasis is laid capitally on the influence of the epoxide casting mixture composition. The thesis describes the manufacture technology including used methodics and materials. The compositions of epoxide resins and the mechanisms of their curing. Also, the definitions of fundamental properties of dielectric materials and the description of diagnostic methods used to relative permitivity, dissipation factor and inner resistivity are included. suitable casts of acquired samples were set and dried out within the experimental part, followed by measurement of fundamental electrical properties in temperature and frequency relations. Hereafter a comparison of individual samples and the evaluation of their electrical properties will be carried out.
|
|
|
Methodology of Determination of Electroinsulating Properties
Čanigová, Veronika ; Nevřivová, Lenka (referee) ; Sokolář, Radomír (advisor)
The core of this bachelor thesis is porcelain and electrical porcelain property specification accompanied by definition and explanation of electric conductivity. The theoretical section provides insight into electrical porcelain production from initial raw material exploitation to final stages of body baking. The experimental part compiles a number of electrical porcelain test methods based on current European standards and draft test procedures, which are followed in order to specify properties of conventional electrical porcelain as well as emerging anorthite porcelain based on aluminate cement.
|
|
|
Electrical properties analysis of epoxy resins with various fillers
Horák, Luděk ; Kazelle, Jiří (referee) ; Frk, Martin (advisor)
Presented bachelor thesis is focused on studying electroinsulating epoxy resin-based sealings. It describes the chemical composition, production, properties and measuring methods of basic electric quantities of these materials. This work also embodies a preparation of composite epoxy resin samples with different kinds of micro-ground siliceous sand as a filling. The samples given are measured on the temperature dependency of relative permitivity, dissipation factor and inner resistivity.
|
|
|
Study of the influence of fillers and external conditions on the resistivity of cement composites
Kejda, Dalibor ; Melichar, Jindřich (referee) ; Černý, Vít (advisor)
The progress of new materials is important for the construction industry. Modern materials include cement composites with reduced resistivity. This is achieved by adding suitable electrically conductive fillers. If there is enough of these fillers, the so-called percolation threshold occurs. Suitable fillers (Condufit C4 and Supragraphite C300) have been proposed. Recipes have been designed to be before and after the percolation threshold. The tests were performed on beams measuring 40x40x160 mm with built-in electrodes for measuring their resistivity. The aim of the work was the research of influencing external conditions on cement composites. The effect of temperature was verified. The lowest values of resistivity were evaluated at temperatures of 50 ° C and the resistivity increased with decreasing temperature. The effect of humidity on the resistivity was then verified. Reference samples and samples with a smaller proportion of graphite powder showed larger differences in resistivities with increasing humidity. The samples above the percolation threshold were not much affected by increasing humidity. Finally, the effect of loading on the resistivity of the samples was verified. Almost all samples with increasing compressive stress showed an increasing value of resistivity.
|
|
|
Study of the influence of structure on the resistivity of silicate composites
Uher, Vojtěch ; Šteffan,, Pavel (referee) ; Drochytka, Rostislav (advisor)
Electroconductive silicate-based composites are advanced materials that allow building structures to perform several different functions simultaneously. Addressing the issues of their development and use is a suitable topic for research work. The aim of this work is to study the effect of structure on the resistivity of silicate composite. The structure of electrically conductive composites is studied on dry cement paste and mortar mixtures as well as on test bodies made of hardened cement paste and mortar after 28 days of curing. Based on the analysis of the raw materials, six suitable electroconductive fillers are selected based on particle size, resistivity, and water absorption. The parameters of dry cement paste and hardened cement paste with replacement of 4-19 wt. % cement by the selected fillers are determined. Two of the fillers are selected for use in dry and hardened mortar. Resistivity is determined for all dry mixes and hardened composites variants, and percolation thresholds are approximately determined. By studying the structure of the selected variants, it is shown that the most important parameters that have the greatest influence on the resistivity of the silicate composites are mainly the particle size and the intrinsic resistivity of the electrically conductive filler. For silicate composites in the hardened state, the volume of hydration products, especially portlandite and C-S-H gels, also has a significant influence. For both dry blends and hardened composites, it was found that the smaller the particle size of the electroconductive filler, the smaller the representation needed to reach the percolation threshold. Portlandite and C-S-H gels in the volume of the hardened composite cause its high resistivity. The resistivity of the hardened composite is always higher than that of the dry blends. Thus, the proportion of electroconductive filler needed to reach the percolation threshold is higher in hardened composites than in dry mixes. The resist
|
|
|
Problems of measurement and evaluation of earth resistance
Šindelář, Petr ; Janda, Marcel (referee) ; Veselka, František (advisor)
This work deals with the measurement of earth resistance, definition, substances causing earth conductivity, basic norms for carrying out grounding revisions and effect of earth resistance on securing and protection element. In the introduction there is theoretical analyzing of grounding issue and principles for the measurement of parameters, which are important for the protection of persons and animals in order not to touch exposed conductive part accidentally, protection of equipment against high fault current and dangerous surges while the correct function of the connected electrical equipment. In the next part there are described methods of earth resistance and soil resistivity measuring. The practical part of the work summarizes the results of practical measurements in individual places with different measuring device.
|
|
|
Study of electrical properties of nanocomposites
Ovsík, Jiří ; Rozsívalová, Zdenka (referee) ; Polsterová, Helena (advisor)
The present work deals with the electrical properties of nanocomposite materials. Samples for the experiment are made of epoxy resin as a matrix and oxides TiO2, Al2O3, WO3, SiO2 as nanofillers in 0.5 and 1 percent performance. The experimental samples are measured in temperature and frequency dependence of relative permittivity, dissipation factor, rezistivity and are broken down by the influence of filler on the electrical properties of the polymer. Attention is also paid to the mechanical properties of nanocomposites.
|
|
|
Measurement of HV equipments by electronic bridge.
Kumičák, Ivan ; Pelikán, Luděk (referee) ; Krbal, Michal (advisor)
The main idea of this thesis is measurements of dielectric materials by using a device Tettex. The thesis is about basic physic properties of dielectric materials. The determination of a dielectric material is considered. The behavior of these materials in electrical fields and reasons, those can have an influence on it, are considered as well. In the text are described measuring methods of chosen parameters of dielectric materials by device Tettex and its functional principles. There are an evaluation of measurements, which were done, and a discussion about achieved results.
|
|
|
Dielectric absorption characteristics of stressed slot insulations
Přikryl, Tomáš ; Frk, Martin (referee) ; Rozsívalová, Zdenka (advisor)
Master's thesis is monitoring changes in basic dielectric properties. Monitoring changes in absorbency of characteristics and temporal dependences in rezistance with change of relative humidity. On the colection samples were measured temporal dependences charged and uncharged currents in ambient temperature and 0%, 55%, 75%, 95% relative humidity. The next part of my work is monitoring temporal dependences interior rezistance in the time of ageing in different humidities. Experiments were made on material ISONOM NKN and NMN.
|
guest ::
